SC452-011-15 Picture Pacific

Description

SC452-011-15 Picture Pacific

SC452-011-15 Picture Pacific

The SC450 series controller is designed for installation in a cabinet. Your installation should meet the following guidelines:

1.Vertical orientation for the controller

2.Flat, solid surface capable of supporting the approximate weight of the units as follows:

SC451 – 6 lbs (2.7 kg)

SC452 – 6 lbs (2.7 kg)

SC453 – 11 lbs (5.0 kg)

Distributed Control System (DCS) is a computer control system based on microprocessors and microcomputers, integrating computer technology, data communication technology, CRT screen display technology, and automatic control technology. It conducts centralized operational management and decentralized control of the production process. Also commonly referred to as Distributed Control Systems (TDCS). After years of development. DCS control technology is becoming increasingly mature and widely used. Has gradually become a protagonist in the field of process control. With the increasing demand of modern power grids for the peak shaving capability of unit units, Automatic Generator Control (AGC) and Automatic Dispatch System (ADS) have emerged, and thermal power plants urgently need to achieve load control based on turbine following or boiler following for single unit units, The INFI-90 control system introduced by a certain power plant includes the internationally advanced Coordinated Control System (CCS), which can achieve high-quality coordinated control of units. In the practice of coordinating control system investment, the fluctuation problem of load control response and pressure control was solved by modifying the control strategy. The on-site operation shows that the improvement work of the control system is effective, and the effect of coordinating the control system is relatively ideal.

Coordinated control system control method
The coordinated control system combines various automatic control subsystems in a certain way to jointly adapt to changes in unit load, ensuring stable operation of the unit and rapid response to load. Due to the differences in dynamic characteristics, the CCS control system must carry out necessary task coordination between machines and boilers to improve the boiler regulation speed. To maintain the material and energy balance during the load adjustment process, the combustion and water supply automatic control system of the unit must have good regulation and anti-interference performance. At the same time, the CCS control system must have certain fault handling capabilities, and the coordinated main control system is shown in Figure 1.

In order to adapt to the operating conditions of the unit and ensure its safe operation, five operating modes have been set up from the control strategy: ① turbine boiler open loop control, ② machine boiler control, ③ furnace machine control, ④ coordinated control based on turbine following, and ⑤ coordinated control based on boiler following. Among them, 4 is the highest form of unit operation and the foundation for achieving unit ACC. 5 is also an advanced mode of unit operation, but due to the fact that the unit in the factory is a direct flow boiler unit with a direct blowing pulverizing system, the boiler pressure regulation method is difficult to stabilize the unit’s operating conditions during actual operation, and it is not recommended to apply it after testing. The CCS switching logic is shown in Figure 2.

Model Product:
6062NZ10300
606-AS
607980-71B
60990-2-T306
60M100-00
60WKS-CE240/12PB
60WKS-CE240/22PB
60WKS-M240/22
60WKS-M240/6-PO
6100BZ10010B
6101BZ10010A
6129863-1C
6151NB10700
6152NB10700
6153NB10700
61615-0-1200000
6176M-15PT
6176M-17PT
6177R-M3PXP
6180P-15BPXP
6180P-15BPXPDC
6180W-12BPXPHDC
6181F-17TSXP
6181P-12A2MW71DC
6181P-15A3MWX1AC
6181P-15TPXP
6181P-15TPXPH
6181P-15TSXP
6181P-17A2MW71DC
6181P-17TPW7
6181P-17TPXPH
6181P-17TSXP
6181X-12TPXPDC
6186-M15ALTR
6186M-15PT
6186M-15T
6186M-17PT
6186-M19ALTR
6189-RDT10C