Name: MVME374-001 MOTOROLA Controller Board
Price: 4322 CNY
Availability: InStock

Description

To produce the desired configuration and ensure proper operation of the MVME374-001, you may need to carry out certain hardware modifications before installing the module. The MVME374-001 provides software control over most options: by setting bits in control registers after installing the module in a system, you can modify its configuration. (The MVME374-001 registers are described in Chapter 3 under ENV – Set Environment, and/or in the MVME374-001 VME Embedded Controller Programmer’s Reference Guide as listed in “Related Documentation” in Appendix E.) Some options, however, are not software-programmable. Such options are controlled through manual installation or removal of header jumpers or interface modules on the base board.
Turn the system’s power off before you perform these procedures. Failure to turn the power off before opening the enclosure can result in personal injury or damage to the equipment. Hazardous voltage, current, and energy levels are present in the chassis. Hazardous voltages may be present on power switch terminals even when the power switch is off. Never operate the system with the cover removed. Always replace the cover before powering up the system.
This section applies to all hardware installations you may perform that involve the MVME374-001 board. Motorola strongly recommends the use of an antistatic wrist strap and a conductive foam pad when you install or upgrade the board. Electronic components can be extremely sensitive to ESD. After removing the board from the chassis or from its protective wrapper, place the board flat on a grounded, static-free surface, component side up. Do not slide the board over any surface. If no ESD station is available, you can avoid damage resulting from ESD by wearing an antistatic wrist strap (available at electronics stores). Place the strap around your wrist and attach the grounding end (usually a piece of copper foil or an alligator clip) to an electrical ground. An electrical ground can be a piece of metal that literally runs into the ground (such as an unpainted metal pipe) or a metal part of a grounded electrical appliance. An appliance is grounded if it has a three-prong plug and is plugged into a three-prong grounded outlet. You cannot use the chassis in which you are installing the MVME374-001 itself as a ground, because the enclosure is unplugged while you work on it.
The IP bus clock speed may be either 8MHz or the speed of the local bus clock (30MHz for the MC68060, 32MHz for the MC68LC060). The default factory configuration has a jumper installed on J11 pins 1 and 2, denoting an 8MHz clock.

MVME374-001 PDF
MVME374-001

♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦

Shipping:
1. Your item will be shipped to all countries via EMS, unless one country cannot be shipped via EMS. We will choose DHL, UPS, or FedEx. Please leave us your phone number.
2. We will ship the product to you on the same day or within 1-2 working days after receiving your payment. The shipping time depends on the country/region where you reside, the customs and habits of your country/region, and especially during peak hours.
3. Assuming (assuming) that the item requires payment of tariffs from your country, the buyer is obligated. We are not responsible for any taxes or customs fees in your country/region.

Return Policy:
1. Please contact us before returning the item.
2. The buyer should inform the seller of all returned items within 7 days after receiving the package. We reserve the right to reject any request to inform the seller for more than 7 days.
3. Returned products must have all original packaging and be in good condition.

Response policy:
If you are satisfied with the purchase, please leave us an active response.
2. If you have any questions about the outcome of the transaction or product, please contact us first and we will do our best to satisfy you!
3. Please do not reply with negative feedback before contacting us!