Description

Wiring Method for Model 5C5601.32

Pre-wiring Preparation

Confirm that the power supply of the system where the 5C5601.32 module is located has been cut off, and verify the power-off state with a multimeter to avoid electric shock hazards.

Check the integrity of the module terminals: ensure that terminal pins are free of deformation, oxidation, or looseness; confirm that the terminal block labels (e.g., signal input/output, power supply, ground) are clear and consistent with the product manual.

Prepare matching wiring materials: select cables with appropriate cross-sectional area according to the current and voltage specifications of the module; use shielded cables for analog signal wiring to reduce electromagnetic interference.

Terminal Wiring Specification

2.1 Power Supply Wiring

Identify the power terminals of the module, marked as L+ (positive pole) and M (negative pole) in the product manual.

Connect the positive terminal of the external DC power supply to the L+ terminal of the module, and the negative terminal to the M terminal.

Ensure that the input voltage matches the rated voltage of the module (check the nameplate for parameters, e.g., DC 24V ±10%).

Tighten the terminal screws with a torque wrench (recommended torque: 0.8–1.2 N·m) to prevent poor contact caused by loose screws.

2.2 Signal Input/Output Wiring

Digital Signal Wiring

For digital input channels (marked as DI1–DIx): connect the signal source (e.g., proximity switch, limit switch) to the corresponding DI terminals, and connect the common terminal COM to the power supply reference pole.

For digital output channels (marked as DO1–DOx): connect the load (e.g., contactor coil, indicator light) to the corresponding DO terminals; select the appropriate output type (relay output or transistor output) according to the load voltage and current.

Analog Signal Wiring

For analog input channels (marked as AI1–AIx, e.g., 4–20mA current signal or 0–10V voltage signal):

Adopt two-wire or four-wire connection based on the sensor type.

Connect the shield layer of the cable to the PE (grounding) terminal of the module to suppress electromagnetic interference.

Ensure the signal polarity is correct (positive pole to + terminal, negative pole to – terminal) to avoid module damage.

For analog output channels (marked as AO1–AOx): connect the output terminal to the controlled device (e.g., actuator, regulator), and confirm the signal type matches the device’s input requirements.

2.3 Grounding Wiring

Connect the PE terminal of the module to the system’s protective ground (PGND) to ensure reliable grounding.

The grounding resistance should be less than 4Ω to ensure the module’s stable operation and lightning protection performance.

Avoid sharing the grounding wire with high-power equipment to prevent ground loop interference.

Post-wiring Inspection

Conduct a visual inspection: check whether all wiring is correctly connected according to the diagram, whether the terminal screws are tightened, and whether the cable arrangement is neat (avoid crossing with high-voltage cables).

Conduct a continuity test: use a multimeter to check the continuity of each circuit to ensure no short circuit or open circuit.

Power-on test: power on the module and check the indicator light status (power indicator is on, no fault indicator is on); verify the signal transmission accuracy through the upper computer system.

5C5601.32 PDF
5C5601.32_加水印

♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦♦…♦

Shipping:
1. Your item will be shipped to all countries via EMS, unless one country cannot be shipped via EMS. We will choose DHL, UPS, or FedEx. Please leave us your phone number.
2. We will ship the product to you on the same day or within 1-2 working days after receiving your payment. The shipping time depends on the country/region where you reside, the customs and habits of your country/region, and especially during peak hours.
3. Assuming (assuming) that the item requires payment of tariffs from your country, the buyer is obligated. We are not responsible for any taxes or customs fees in your country/region.

Return Policy:
1. Please contact us before returning the item.
2. The buyer should inform the seller of all returned items within 7 days after receiving the package. We reserve the right to reject any request to inform the seller for more than 7 days.
3. Returned products must have all original packaging and be in good condition.

Response policy:
If you are satisfied with the purchase, please leave us an active response.
2. If you have any questions about the outcome of the transaction or product, please contact us first and we will do our best to satisfy you!
3. Please do not reply with negative feedback before contacting us!